Topic: Cannot format a froozen disk
Hello,
I have a special problem with a Flash Sata Disk were i do erase NTFS partitions but when reboot they still there, i did try to create an EXT4 partition but i get this error:
GParted 0.26.0 --enable-libparted-dmraid --enable-online-resize
Libparted 3.2
Create Primary Partition #1 (ext4, 4.77 GiB) on /dev/sdb 00:00:34 ( ERROR )
create empty partition 00:00:00 ( SUCCESS )
path: /dev/sdb1 (partition)
start: 2048
end: 10004479
size: 10002432 (4.77 GiB)
clear old file system signatures in /dev/sdb1 00:00:00 ( SUCCESS )
write 512.00 KiB of zeros at byte offset 0 00:00:00 ( SUCCESS )
write 4.00 KiB of zeros at byte offset 67108864 00:00:00 ( SUCCESS )
write 512.00 KiB of zeros at byte offset 5120720896 00:00:00 ( SUCCESS )
write 4.00 KiB of zeros at byte offset 5121179648 00:00:00 ( SUCCESS )
write 8.00 KiB of zeros at byte offset 5121236992 00:00:00 ( SUCCESS )
flush operating system cache of /dev/sdb 00:00:00 ( SUCCESS )
set partition type on /dev/sdb1 00:00:01 ( SUCCESS )
new partition type: ext4
create new ext4 file system 00:00:33 ( ERROR )
mkfs.ext4 -F -L "" /dev/sdb1 00:00:33 ( ERROR )
Creating filesystem with 1250304 4k blocks and 312624 inodes
Filesystem UUID: 7da720c3-ff8b-4e42-904e-875039d4fed1
Superblock backups stored on blocks:
32768, 98304, 163840, 229376, 294912, 819200, 884736
Allocating group tables: done
Writing inode tables: done
Creating journal (32768 blocks): done
Writing superblocks and filesystem accounting information:
mke2fs 1.42.13 (17-May-2015)
Warning, had trouble writing out superblocks.
========================================
And after reboot the partitions and data still there again like in a CD, that's why i tougth that it was a write protection issue,
I did also try to erase the disk with hdparm, testdisk and dd but it does not work, even i did try to rescue it with the windows diskpart tool in order to clear the froozen flag with no success. Everytime i thing i am getting the solution de disk comes with the input/output error so i have to reconnect it to start over.
the info of the disk:
ADATA PREMIER PRO SP600S3-128GB
--------------------------------------------------------------------------
/dev/sdb:
ATA device, with non-removable media
Model Number: ,iO�##i#/H�##�#P�9HA#�#�($�#�6�&7�##
Serial Number: �1#�#@Z�P
##f�=#
Firmware Revision: ##|p##`
Media Serial Num: S�����#��h#��>&�q�#�y��)�ª>"+#�U�t�
Media Manufacturer: �ٗ�.�"�;���##y
hAl]
Transport: 0xe0f2; Revision: 0x1302
Standards:
Used: unknown (minor revision code 0x8645)
Supported: 14 12 8 6
Likely used: 14
Configuration:
Logical max current
cylinders 47617 48708
heads 27375 54493
sectors/track 63683 1990
--
CHS current addressable sectors: 1612857681
LBA user addressable sectors: 92274693
Logical/Physical Sector size: 512 bytes
device size with M = 1024*1024: 787528 MBytes
device size with M = 1000*1000: 825783 MBytes (825 GB)
cache/buffer size = unknown
Nominal Media Rotation Rate: 64178
Capabilities:
LBA, IORDY(may be)(can be disabled)
Standby timer values: spec'd by Standard
R/W multiple sector transfer: Max = 66 Current = ?
Recommended acoustic management value: 118, current value: 71
DMA: *mdma0 *mdma1 *mdma3 mdma7 udma0 *udma4 *udma7 (?)
PIO: unknown
Commands/features:
Enabled Supported:
Write cache
WRITE_BUFFER command
* DOWNLOAD_MICROCODE
Removable Media Status Notification feature set
* SET_FEATURES required to spinup after power up
* SET_MAX security extension
Device Configuration Overlay feature set
* unknown 76[0]
* Gen1 signaling speed (1.5Gb/s)
* Phy event counters
* READ_LOG_DMA_EXT equivalent to READ_LOG_EXT
* unknown 78[0]
unknown 78[12]
* unknown 78[14]
* unknown 78[15]
* SMART Command Transport (SCT) feature set
* SCT Error Recovery Control (AC3)
* SCT Data Tables (AC5)
unknown 206[7]
unknown 206[8]
unknown 206[10]
unknown 206[11]
unknown 206[14] (vendor specific)
* reserved 69[0]
* reserved 69[1]
* reserved 69[6]
* DOWNLOAD MICROCODE DMA command
* READ BUFFER DMA command
* Data Set Management TRIM supported (limit 26619 blocks)
* Deterministic read data after TRIM
Removable Media Status Notification feature set supported
HW reset results:
CBLID- below Vih
Device num = 1 determined by the jumper
Integrity word not set (found 0xafdc, expected 0x6fa5)
---------------------------------------------------------------------------------
when i try to mount it, this is what appears:
Error mounting /dev/sdb2 at /run/media/one/64008E56008E2EDC: Command-line `mount -t "ntfs" -o "uhelper=udisks2,nodev,nosuid,uid=1000,gid=1000" "/dev/sdb2" "/run/media/one/64008E56008E2EDC"' exited with non-zero exit status 14: Windows is hibernated, refused to mount.
Failed to mount '/dev/sdb2': Operation not permitted
The NTFS partition is in an unsafe state. Please resume and shutdown
Windows fully (no hibernation or fast restarting), or mount the volume
read-only with the 'ro' mount option.
.
do you have any idea of what should i do?
THANKS IN ADVANCE...